Can I Set Up a Tub Myself? Considerations And Also Steps
Can I Set Up a Tub Myself? Considerations And Also Steps
Blog Article
Were you searching for tips concerning How to Install a Bathtub?
Mounting a tub isn't exactly brain surgery, however it does require solid plumbing, carpentry, as well as occasionally, tiling skills. Replacing an old bath tub with a new one is also a reasonably difficult task. If the old tub is conveniently easily accessible, the project can relocate rapidly; if you have to open up a wall to remove the old bathtub as well as position the brand-new bath tub, the task is much harder. In either instance, the job is within a home handyman's abilities, although you will certainly need a helper to move out the old bathtub as well as set in the brand-new one. Make sure you have actually qualified yourself for the task and are comfortable attempting it. As opposed to employing a contractor to take control of a halfway-completed project, it is far better to think about employing one before you start. Possibilities are you might need a professional plumber to make tube links.
This post will assist you install a brand-new bathtub in your shower room if you have currently bought a brand-new tub as well as don't require to transform the plan of your previous water system pipelines.
Your tools and also material list need to consist of the following:
Planning for the Setup
To start with, the supporting framework provided with the bath must be fitted (if called for) according to the producer's guidelines. Next off, fit the taps or mixer to the tub. When suitable the tap block, it is essential to make certain that if the tap includes a plastic washing machine, it is fitted between the bathroom and also the taps. On a plastic bath, it is additionally sensible to fit a supporting plate under the taps unit to avoid stress on the tub.
Fit the adaptable faucet ports to the bottom of both faucets using 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet through the hole in the bath. Use the nut supplied by the producer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. See to it you make use of all of the supplied washers.
Link the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom need to currently be ready to be fitted in its final position.
Removing Old Touches
If you require to change old faucets with new ones as a part of your setup, then the first thing you should do is separate the water system. After doing so, activate the taps to drain pipes any water continuing to be in the system. The process of getting rid of the existing taps can be quite bothersome because of the restricted accessibility that is frequently the situation.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipelines to the faucets. Have a cloth prepared for the staying water that will certainly originate from the pipes. As soon as the supply pipelines have been removed, utilize the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary faucets from transforming throughout this procedure. Once the faucets have actually been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any kind of old sealing substance.
Before going on to fit the new taps, contrast the pipe links on the old taps to the brand-new taps. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the new taps to fit.
Mounting the Tub
Using both wood boards under its feet, place the bath tub in the called for setting. The wooden boards are valuable in evenly spreading out the weight of the tub over the location of the boards as opposed to concentrating all the weight onto 4 tiny factors.
The following objective is to make sure that the tub is leveled all round. This can be achieved by checking the spirit level and changing the feet on the bathtub until the spirit level checks out level.
To set up faucets, fit all-time low of the furthest flexible faucet adapter to the appropriate supply pipe by making a compression sign up with; after that do the very same for the various other faucet.
Switch on the water supply as well as inspect all joints and also brand-new pipework for leakages and tighten them if essential. Fill up the bath tub and also inspect the overflow electrical outlet and the normal outlet for leaks.
Lastly, take care of the bathroom paneling as defined in the maker's user's manual. Tiling and securing around the bath tub should wait up until the bath tub has been utilized a minimum of when as this will resolve it into its final placement.
Suitable New Taps
If the tails of the new faucets are plastic, after that you will certainly require a plastic connector to prevent damage to the string. One end of the port fits on the plastic tail of the faucet as well as the various other end provides a connection to the current supply pipes.
If you require to fit a monobloc, after that you will need decreasing couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, position the faucet in the placing hole in the bath/basin making sure that the washers remain in place between the tap as well as the sink. Safeguard the tap in place with the supplier offered backnut. As soon as the tap is safely in position, the supply pipes can be linked to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with regular faucet connectors. The previous kind ought to be attached to the tap ends initially, tightening up only by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the location where the bath satisfies the ceramic tile, it is essential to seal the joins with a silicone rubber caulking. This is necessary as the fitting can move sufficient to split an inflexible seal, causing the water to permeate the wall between the bathroom as well as the tiling, bring about complications with moisture as well as feasible leakages to the ceiling listed below.
You can choose from a variety of coloured sealants to assimilate your components and fittings. They are marketed in tubes as well as cartridges, as well as are capable of sealing spaces as much as a width of 3mm (1/8 inch). If you have a larger gap to load, you can load it with spins of drenched paper or soft rope. Keep in mind to always fill up the bathtub with water before securing, to permit the activity experienced when the bathtub remains in usage. The sealant can break rather very early if you do not think about this activity prior to securing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally easily available on the market. It is recommended to fit the tiles using water-resistant or waterproof glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We had been introduced to that editorial on How to Install a Bathtub Yourself through a friend on our other blog. For those who liked our blog entry plz be sure to share it. Thanks so much for taking the time to read it.
Contact
Report this page